- Posts: 4557
- Thank you received: 76
Wheels
- dmcdona
- Topic Author
- Offline
- Administrator
Less
More
16 years 8 months ago #66164
by dmcdona
Wheels was created by dmcdona
Folks, I'm looking to replace the wheels on my rolling observatory. Think of a garden shed without a floor and a wheel near each corner - that's my rolling observatory...
I'm going to replace the wheels - the replacement wheels have a 1" diameter hole to take an "axle". The supplier doesn't sell these - only the wheels.
I was thinking that a 1" bolt would do the trick, as long as it is long enough. The width of the wheel is 95mm. The width of the central piece (where the "axle" goes) is 66mm.
You may have guessed that at this point, I haven't got a scooby when it comes to motor vehicle mechanics...
So, the question is, what do I need to get to mount these wheels?
Cheers
Dave
I'm going to replace the wheels - the replacement wheels have a 1" diameter hole to take an "axle". The supplier doesn't sell these - only the wheels.
I was thinking that a 1" bolt would do the trick, as long as it is long enough. The width of the wheel is 95mm. The width of the central piece (where the "axle" goes) is 66mm.
You may have guessed that at this point, I haven't got a scooby when it comes to motor vehicle mechanics...
So, the question is, what do I need to get to mount these wheels?
Cheers
Dave
Please Log in or Create an account to join the conversation.
- philiplardner
- Offline
- Red Giant
16 years 8 months ago #66167
by philiplardner
A big hammer!
If you haven't already bought the wheels then check out Castormart in the Ballymount Ind. Est.
www.castormart.com/index.htm
They might have something better - or provide some inspiration.
Phil.
Replied by philiplardner on topic Re: Wheels
So, the question is, what do I need to get to mount these wheels?
A big hammer!
If you haven't already bought the wheels then check out Castormart in the Ballymount Ind. Est.
www.castormart.com/index.htm
They might have something better - or provide some inspiration.
Phil.
Please Log in or Create an account to join the conversation.
- dmcdona
- Topic Author
- Offline
- Administrator
Less
More
- Posts: 4557
- Thank you received: 76
16 years 8 months ago #66168
by dmcdona
Replied by dmcdona on topic Re: Wheels
Cheers Phil - I didn't take the plunge yet so that might be the place to go!
Please Log in or Create an account to join the conversation.
- JohnMurphy
- Offline
- Super Giant
16 years 8 months ago #66188
by JohnMurphy
Clear Skies,
John Murphy
Irish Astronomical Society
Check out My Photos
Replied by JohnMurphy on topic Re: Wheels
You might find it hard to find a 1" diameter bolt. However you may find bearings to fit in the wheel hub and use large washers on either side and fix a smaller bolt equal to the internal diameter of the bearings. The bearings would also produce a smoother ride. Just my 2c - I'll get me coat now
Clear Skies,
John Murphy
Irish Astronomical Society
Check out My Photos
Please Log in or Create an account to join the conversation.
- DaveGrennan
- Offline
- IFAS Astronomer of the Year 2010
Less
More
- Posts: 2707
- Thank you received: 32
16 years 8 months ago #66195
by DaveGrennan
Regards and Clear Skies,
Dave.
J41 - Raheny Observatory.
www.webtreatz.com
Equipment List here
Replied by DaveGrennan on topic Re: Wheels
Dave,
1" Steel tubing shouldn't be hard to find. It will certainly be strong enough and would also be easy to work with. Radionics have 1" steel tubing 18swg (1.21mm thick)
tinyurl.com/5v2a3d
1" Steel tubing shouldn't be hard to find. It will certainly be strong enough and would also be easy to work with. Radionics have 1" steel tubing 18swg (1.21mm thick)
tinyurl.com/5v2a3d
Regards and Clear Skies,
Dave.
J41 - Raheny Observatory.
www.webtreatz.com
Equipment List here
Please Log in or Create an account to join the conversation.
- michaeloconnell
- Offline
- Administrator
Less
More
- Posts: 6332
- Thank you received: 315
16 years 8 months ago #66200
by michaeloconnell
Replied by michaeloconnell on topic Re: Wheels
You could always splash out and get a set of 18" alloys!
Please Log in or Create an account to join the conversation.
Time to create page: 0.120 seconds